+- Beamicon2 Support Forum (https://beamicon2basic.com/forum)
+-- Forum: English language forum for Beamcion2 Basic users (https://beamicon2basic.com/forum/forum-3.html)
+--- Forum: Open forum (https://beamicon2basic.com/forum/forum-12.html)
+--- Thread: Beamicon2 (3.24) Linux does not start (Asks for parameter files...) (/thread-196.html)
Beamicon2 (3.24) Linux does not start (Asks for parameter files...) - Meirssv1 - 10-03-2025
Hello,
I am eagerly waiting for my ordered CNC-machine from CNC-STEP. I want to try out the Beamicon2 software on a linux machine. (Linux Mint, debian based)
Installation went fine, but when trying to start the application I get this error message:
"Parameter files don't exist or are corrupted, Please re-install the program"
Can someone help me on this issue please?
Ok, forget my remark. I removed it and then reïnstalled it from the command line -as root- and run it as root and it works now!
RE: Beamicon2 (3.24) Linux does not start (Asks for parameter files...) - Admin - 10-04-2025
You must install and run the program as root.
The package is build for debian with lxde gui.
If you use different versions it can be possible, that some depencies are different and/or missing.
RE: Beamicon2 (3.24) Linux does not start (Asks for parameter files...) - Meirssv1 - 10-04-2025
(10-04-2025, 08:22 AM)Admin Wrote: You must install and run the program as root.
The package is build for debian with lxde gui.
If you use different versions it can be possible, that some depencies are different and/or missing.
Yes, I saw it after I posted the original message, see at the bottom of it. I saw the German explanation, I could make up what I had to do
. It starts up now, no errors.By using Beamicon2 with the zero4 controller of CNC-STEP, I assume the performance of the host running Beamicon2 is not that ciritcal, am I correct? I will install this on a Seeed Studio reTerminal DM, which will be a nice combo with the CNC Machine.
RE: Beamicon2 (3.24) Linux does not start (Asks for parameter files...) - Admin - 10-04-2025
But the Kintec-NC controller dont work with Beamicon!
You can test the Software, but to run the Controller from CNC Step you must switch to Kinetc-NC Software.
RE: Beamicon2 (3.24) Linux does not start (Asks for parameter files...) - Meirssv1 - 10-04-2025
Oh no. That is so bad news.
I also downloaded the Kinetic-NC software (and tried it out on a Windows VM) for comparison and I assumed Beamicon2 would also work, because I thought they are both from Benezan Electronics.I hope I don't get stuck with a Windows requirement because I explicitly asked for Linux support when I ordered the CNC-STEP machine.
RE: Beamicon2 (3.24) Linux does not start (Asks for parameter files...) - Admin - 10-05-2025
But Kinetic should run in a VM without problems :-)
KinetiC-NC and Beamicon2 are nearly the same, the main problem are that KinetiC-NC is OEM and supportet by CNC-Step.
For this reason Hardware from CNC-Step can not run under Beamicon2.
RE: Beamicon2 (3.24) Linux does not start (Asks for parameter files...) - Meirssv1 - 10-05-2025
(10-05-2025, 09:59 AM)Admin Wrote: But Kinetic should run in a VM without problems :-)
Well, I went ahead and installed a Win7 on one of my ESXI servers. As I cannot get 3D HW acceleration configured, I allocated 8 cores, 16Gb RAM and it seems to work. Will now try to get the reTerminal DM to act as a 'thin client' to the Win7.